Unexpected faults on our systems seem to have become an inextricable part of our life, no matter how hard we try to avoid them. One such mistake is the “scanning and repairing drive stuck” error. When attempting to boot a Windows PC, this error appears. When this issue happens, your computer will become stuck for an extended period of time.
This problem can occur for a variety of reasons, and it can be quite inconvenient if users must wait hours before the machine wakes up properly. So, if you’ve run into this problem and are keen to know how to remedy it, here’s a blog post that includes six practical remedies for Windows 10 scanning and repairing drive Stuck at 0, 10, 100 error.
- 1 How To Fix “Scanning and Repairing Drive Stuck at 100” in Windows 10
- 1.0.1 1.Wait till the’scanning and repairing drive’ operation is completed before proceeding.
- 1.0.2 2.It’s a good idea to double-check the disc connection.
- 1.0.3 3.Turn off Windows’ automatic repair feature.
- 1.0.4 4.Disable the automatic Chkdsk check.
- 1.0.5 5. Check file systems
- 1.0.6 6. Try System Restore
- 1.0.7 7. The drive should be stopped from being scanned and fixed in the Windows
- 1.1 Conclusion On How To Fix Scanning and Repairing Drive Stuck at 100
Windows 10 Scanning and Repairing Drive Stuck at 100 Reasons
Windows Automatic Repair is similar to Startup Repair in that it scans drives. When a machine fails to startup, Windows immediately starts the scanning and repair drive procedure. Windows Automatic Repair attempts to scan and repair drives C and D after diagnosing the fault Scanning and Repairing Drive.
When the mistake occurs, it appears as if the hard drive scanning and repair process will go on indefinitely, since it only partially completes and becomes stuck at a specific percentage halfway through.
If the scanning and repair procedure becomes stalled, Windows Automatic Repair is having problems reading the hard disc. The following are the causes of this error.
- Issues with the disc connection
- On the hard disc, there are faulty sectors.
- File systems that have been corrupted
- Drivers that have been configured incorrectly
- Malware assaults
- The computer was forced to shut down or there was a power outage.
How To Fix “Scanning and Repairing Drive Stuck at 100” in Windows 10
You’ll find six options below that can help you fix the repairing drive stuck error.
1.Wait till the’scanning and repairing drive’ operation is completed before proceeding.
The most straightforward solution is to wait a time and see if the problem goes away on its own. When Windows encounters a minor error, it will usually resolve on its own after a short period of time.
If the hard disc is in bad shape, the time it takes to resolve the problem may be extended. If you don’t have that much time, try the advanced solutions listed below to fix the problem.
2.It’s a good idea to double-check the disc connection.
Such mistakes can occur as a result of lost connections. Before proceeding to the advanced solutions, double-check all of the cable connections and ports to ensure that the discs and PC are connected properly.
3.Turn off Windows’ automatic repair feature.
Windows Automatic Repair is a similar process to Startup Repair in that it scans and repairs discs while Windows is booting up. However, this could be the root of the scanning and repair drive stuck error.
You must either enter the Windows Recovery Environment or use the Windows installation disc to stop Automatic Repair. Scanning and Repairing Drive To do it using WinRE, follow the steps below:
- To totally shut down your computer, press the power key for around 10 seconds.
- Restart the computer.
- Press the power button again for a few seconds once you see the PC maker logo on your computer screen to shut down the system.
- Turn on your Windows computer once more. You’ll switch to WinRE mode after the system boots up this time.
- From the “Choose an option” menu, click Troubleshoot and then Advanced options.
- Additionally, choose Command Prompt and type the following command.
- To disable Automatic Repair, type the following commands once more.
- Last but not least, restart your computer.
4.Disable the automatic Chkdsk check.
If the hard disc looks to be in good working order, you can disable CHKDSK on startup by following the steps below.
- By pressing the Windows + R keys, you can enter Safe Mode and then open the Run dialogue box.
- Then press the “OK” button after typing “regedit.”
- Now go to the address listed below.
- From the right-hand pane, select BootExecute.
- After that, you must update the Value Data to “autochk /k:C” in a pop-up window. After that, press the “OK” button.
- After that, quit Safe Mode and reset your computer.
5. Check file systems
If a corrupted file system is causing Windows 10 to scan and fix drives, Scanning and Repairing Drive you can run the system file checker.
- First, you have to go into Safe Mode.
- Then, open Command Prompt as the administrator.
- Now, type “sfc/scannow” and then press the Enter key at the same time.
- Wait until the scan is done, and then turn your PC back on.
6. Try System Restore
If you have made a System Restore point before, you can try to restore your computer to a time when there were no problems.
- Pressing the Power button three times will force the computer to shut down.
- Getting into the Windows Recovery Environment will be easier if you do this.
- Follow the steps below to get to the System Restore wizard from the “Choose an option” screen.
- When the pop-up window appears, click Next.
- Also, choose a restore point and click Next again to keep going.
- The last step is to confirm what you did and click the Finish button.
7. The drive should be stopped from being scanned and fixed in the Windows
You should turn off the Automatic Repair option on your computer and turn off the process that checks the whole disc automatically.
You can skip the option to scan and fix the hard drive when Windows starts up by pressing any key on the keyboard. Here are the steps that need to be taken to make this happen:
- If the scanning and repairing drive is stalled, push the power button to effectively shut down the computer system.
- After turning on the computer, the message ‘Preparing Automatic Repair’ appears on the screen, which further diagnoses the system.
- Before the disc checking process begins, you must disable the disc checking procedure on the machine by pressing any key on the keyboard.
Conclusion On How To Fix Scanning and Repairing Drive Stuck at 100
This mistake can persist for a long time. As a result, if you find yourself in this scenario, you can utilise the six ways listed above to scan and repair the drive stuck error.